Search
Filters
Close

SGMAV-06A3A21 Yaskawa

Cross references:
SGMAV-06A3A2C Yaskawa
SGMAV-06A3A2E Yaskawa
SGMAV-06A3A2S Yaskawa
SGMAV-06A3A61 Yaskawa
SGMAV-06A3A6C Yaskawa
SGMAV-06A3A6E Yaskawa
SGMAV-06A3A6S Yaskawa
SGMAV-06A3AB1 Yaskawa
SGMAV-06A3ABC Yaskawa
SGMAV-06A3ABE Yaskawa
SGMAV-06A3ABS Yaskawa
SGMAV-06ADA21 Yaskawa
SGMAV-06ADA2C Yaskawa
SGMAV-06ADA2E Yaskawa
SGMAV-06ADA2S Yaskawa
SGMAV-06ADA61 Yaskawa
SGMAV-06ADA6C Yaskawa
SGMAV-06ADA6E Yaskawa
SGMAV-06ADA6S Yaskawa
SGMAV-06ADAB1 Yaskawa
SGMAV-06ADABC Yaskawa
SGMAV-06ADABE Yaskawa
SGMAV-06ADABS Yaskawa

Round per minute: 3000/6000 RPM
Voltage: 200 V
Serial: Sigma V


CANADA YASKAWA AUTHORIZED SERVICE CENTRE
Manufacturer part number: SGMAV-06A3A21

SGMAV-06A3A21 Yaskawa

 

 

550 W, 3000/6000 RPM, Serial Sigma V (SGMAV) 

 


Solutions for problems encountered

 

 

 

 

A good-conditioned servomotor operating in an ideal environment can have a very long life span. We are talking about thirty years. During these years, he may encounter troubles that require a specialist's intervention. Here are some examples of problems that can happen:

 

Faulty encoder: When you see the error codes AC9 or AC90 [error code on Yaskawa Products] on your servo-drive, there is a strong likelihood that the encoder is defective.

 

Brake that sticks: when the brake sticks, the motor must use more current in order to do the same work as in normal time. In this case, your servo-drive may present the error code Over Current A10 [error code on Yaskawa products].

 

Motor overheating: There may be several causes for an overheating engine. Prematurely worn bearings, damaged brake or improper parameterisation of the servomotor in the servo-drive when the servomotor configuration does not correspond to the correct application of the servomotor.

 

Motor Vibration: When the motor is unbalanced, it starts to vibrate. Without immediate maintenance, the vibrations will become stronger, which will damage the servomotor. Worn bearings and bearing cages can cause vibration. The more vibration, the more the encoder is likely to get damaged. When the actuator is noisy, there is a good chance that it will be unbalanced.

 

Broken motor Connector: In addition to damaging the motor, this can also damage the servo-drive by causing a short circuit.

 

Unplugged Actuator Connector: A connector that is not plugged into the servomotor, can create a warm up and cause faults such as over Current A10 [error code on Yaskawa products]. This could also damage the servo-drive by causing a short circuit.

 

Accumulation of metal dust on the encoder: When the brake and bearings wear out, they can send metal dust to the encoder. This may affect the readings of the encoder.

 

 

 

 

SGMAV-06A3A21 Yaskawa

 

 

550 W, 3000/6000 RPM, Serial Sigma V (SGMAV) 

 


Solutions for problems encountered

 

 

 

 

A good-conditioned servomotor operating in an ideal environment can have a very long life span. We are talking about thirty years. During these years, he may encounter troubles that require a specialist's intervention. Here are some examples of problems that can happen:

 

Faulty encoder: When you see the error codes AC9 or AC90 [error code on Yaskawa Products] on your servo-drive, there is a strong likelihood that the encoder is defective.

 

Brake that sticks: when the brake sticks, the motor must use more current in order to do the same work as in normal time. In this case, your servo-drive may present the error code Over Current A10 [error code on Yaskawa products].

 

Motor overheating: There may be several causes for an overheating engine. Prematurely worn bearings, damaged brake or improper parameterisation of the servomotor in the servo-drive when the servomotor configuration does not correspond to the correct application of the servomotor.

 

Motor Vibration: When the motor is unbalanced, it starts to vibrate. Without immediate maintenance, the vibrations will become stronger, which will damage the servomotor. Worn bearings and bearing cages can cause vibration. The more vibration, the more the encoder is likely to get damaged. When the actuator is noisy, there is a good chance that it will be unbalanced.

 

Broken motor Connector: In addition to damaging the motor, this can also damage the servo-drive by causing a short circuit.

 

Unplugged Actuator Connector: A connector that is not plugged into the servomotor, can create a warm up and cause faults such as over Current A10 [error code on Yaskawa products]. This could also damage the servo-drive by causing a short circuit.

 

Accumulation of metal dust on the encoder: When the brake and bearings wear out, they can send metal dust to the encoder. This may affect the readings of the encoder.

 

 

 

 

To receive a PDF on the technical documentation of this servo motor, please contact us.